How to Reset Whirlpool Washer Duet

Option 1 – Extend Step 2 to 30 Minutes or Overnight

You are not obligated to immediately reconnect your dryer after unplugging it. You can choose to leave it disconnected for a duration of anywhere between 30 minutes to overnight before plugging it back in. If this extended waiting period doesn’t resolve the issue, you can then proceed to consider option 2.

Option 2 – Lid Lift

Another approach you can attempt is to lift the dryer lid approximately six times within a span of 12 seconds. It’s important to perform this action rapidly. Following this, you can attempt to restart your Duet dryer. However, if this method proves unsuccessful, it’s advisable to move on to option 3.

Option 3 – Factory Reset

Now, let’s delve into option three as our second technique, which serves as an alternative to the General Reset method discussed earlier.

2. Factory Reset

If your Whirlpool Duet dryer fails to reset even after attempting the General reset and the previously mentioned options, you should consider performing a factory reset. This process allows you to restore the dryer to its original settings, essentially bringing it back to a state similar to that of a new dryer.

Here are the steps to execute the factory reset for your dryer:

1. Plug your dryer into the power source and turn it on.
2. Navigate to the factory reset option within the settings menu and select it.
3. Wait for the dryer to complete the factory reset procedure.
4. After the reset, adjust the clock settings as necessary and then connect the dryer to the internet to finalize the online portion of the reset.

It’s important to note that this reset method requires an internet connection and is only compatible with a Duet dryer that has the capability to run online.

However, if your Whirlpool Duet dryer is not starting at all, this factory reset won’t be effective. In such a case, your best course of action would be to revert to the General Reset method.

How to Run Diagnostic On Your Whirlpool Duet Dryer Before Reset

To run diagnostics on your Whirlpool Duet dryer before attempting a reset, follow these steps:

1. Make Sure the Dryer Is in Standby Mode: Ensure that your dryer is not actively running a cycle. If it is, wait for the current cycle to complete and for the dryer to enter standby mode.
2. Access Diagnostic Mode: On most Whirlpool Duet dryers, you can access diagnostic mode by pressing a specific sequence of buttons on the control panel. The exact button sequence may vary depending on your dryer’s model, so consult your dryer’s user manual or use the following general steps:
   • Press and release the “Power” button to turn off the dryer.
   • Press and hold the “Control Lock” or “Child Lock” button for approximately 3 seconds until the indicator light turns on. This button is typically labelled as “Control Lock” and may require holding the button down for a few seconds.
   • While holding the “Control Lock” button, press and release the “Start” button or the button with a downward arrow (sometimes labelled as “Temp” or “Cycle Signal”) three times in quick succession. This should initiate diagnostic mode.
3. Navigate the Diagnostic Mode: Once in diagnostic mode, your dryer will display error codes or diagnostic information on the control panel’s display. These codes or information can help you identify specific issues with your dryer. Refer to your dryer’s user manual for a list of error codes and their meanings.
4. Record Error Codes: Take note of any error codes or diagnostic information displayed on the control panel. These codes will help you pinpoint the problem with your dryer.
5. Exit Diagnostic Mode: To exit diagnostic mode, you can usually press the “Power” button to turn off the dryer. Alternatively, unplug the dryer or switch off the circuit breaker. Afterwards, you can address the specific issue based on the error codes or diagnostic information you recorded.

How to Reset Whirlpool Duet Dryer Sensing?

Resetting the “Sensing” phase on a Whirlpool Duet dryer typically involves interrupting the cycle and restarting it. Here’s how you can reset the “Sensing” phase:

1. Open the Door: If your dryer is stuck in the “Sensing” phase, begin by opening the dryer door. This will pause the cycle.
2. Remove the Load: Check if there’s any clothing or items inside the dryer drum. Remove them if necessary.
3. Close the Door: Close the dryer door securely.
4. Select a New Cycle: Turn the cycle selector knob to choose a new drying cycle that suits your laundry load. Make sure you select the appropriate settings for your garments.
5. Press the Start Button: Press the “Start” button to initiate the new cycle.
6. Monitor the Dryer: Observe the dryer as it starts the new cycle. It should begin operating normally without getting stuck in the “Sensing” phase.
7. Complete the Cycle: Allow the dryer to run through the selected cycle until your laundry is adequately dried. If it encounters any issues or errors during this cycle, it may display an error code on the control panel. Refer to your dryer’s user manual to interpret the error code and address any underlying problems.

Conclusion

In conclusion, understanding how to troubleshoot and reset your Whirlpool Duet dryer can be a valuable skill to have when facing common issues such as startup problems, error codes, or being stuck in the “Sensing” phase.

We’ve explored various reset techniques, including the general reset, extended waiting periods, and factory resets, which can often resolve these issues effectively. Additionally, running diagnostics before attempting a reset can help identify specific problems.

By following the appropriate steps and consulting your dryer’s user manual for model-specific guidance, you can restore your Whirlpool Duet dryer to its optimal functionality.

Remember that if you encounter persistent issues or are unsure about the troubleshooting process, seeking professional appliance repair assistance may be the best course of action to ensure the longevity and efficiency of your dryer.